Stockpile inventory software for aggregate yards that counts every pile from one drone flight and turns it into tons and dollars
Stockpile inventory software turns a drone flight of your yard into a count of every pile: volume from a surface model, tons from your density factor, dollars from your cost per ton. DroneMapping processes the photos in the browser and gives you cut, fill and net volume per pile, a CSV for your inventory sheet and, on Team and above, a PDF stockpile report. Team is $1,488 a year with 10 seats, and the price does not change when you add a pile, a material or a yard.
net volume
net volume
The month-end gap
Why the book number and the yard number drift apart
Most yards carry inventory in a spreadsheet or an ERP: receipts in, tickets out, a running balance per product. Scale tickets miss spillage, moisture, contamination and loader scoops that never got weighed, so the book balance slowly walks away from the pile. The usual fix is a once a year count by an eyeball estimate or a survey crew, which is exactly when a surprise write-down lands in the audit.
A monthly drone flight changes the timing. The yard is measured from the same surface every month, so a variance shows up in 30 days at a few hundred tons, not after a year at several thousand.
- Every pile on the site captured in one flight
- A saved surface, so any number can be checked again later
- Volume, tons and dollars per pile, ready for the close
From photos to tons
How a drone count becomes an inventory number
The flight gives a digital surface model of the yard. You draw the toe line around each pile on the orthomosaic and pick a base plane: lowest point for piles on a flat pad, average of the perimeter for most yard piles, or a custom elevation for bins and piles against a slab. Each pile returns volume, area, perimeter and maximum height, with the base plane method printed next to the result.
Tons are a multiplication you control. Volume in cubic yards times the loose density of that product gives tons, and the density comes from your own weighed loads, not from a table, because crushed limestone, washed sand and recycled base differ by yard and by season. Export the measurement table as CSV on every plan, add a density column and a cost per ton column, and the sheet gives you dollars per pile. The base plane choice is explained on the stockpile volume measurement page, and the flight settings that keep volumes defensible are in the stockpile volume guide.

Worked example
One pile, from volume to a write-down
Take a pile of crushed limestone that the books say holds 6,300 tons. The drone surface gives 4,200 cubic yards. The yard's weighed loads show 1.4 tons per cubic yard loose, and the product costs $18 a ton. These figures are an example to show the arithmetic, so use your own weighed density and cost.
| Step | Value |
|---|---|
| Measured volume | 4,200 cubic yards |
| Density from weighed loads | 1.4 tons per cubic yard |
| Measured inventory | 5,880 tons |
| Book inventory | 6,300 tons |
| Variance | 420 tons short, 6.7 percent of book |
| Value at $18 a ton | $7,560 |
One pile, one month, a five-figure question answered in an afternoon. Repeat the count next month on the same toe line and the same base plane method, and the report lines up pile for pile, which is what an auditor wants to see.
Month-end close
A stockpile report that goes into the audit file
On Team and above each measured pile goes into a PDF stockpile report: a map of the site with the toe lines, a table with pile name, material, volume and the base plane used, and the flight date. The CSV carries the same table for your spreadsheet. If the count has to land in an ERP or accounting system, a data integration platform such as adapters.io can move the exported rows into it on a schedule, so nobody retypes them. Site managers and finance open a view link in any browser, and view links need no seat.
- Pile name and material per row
- Cut, fill and net volume in cubic yards or cubic meters
- Base plane method printed with every number
- CSV on every plan, PDF stockpile report on Team and above
How the options compare
Stockpile inventory software against the usual ways to count a yard
Prices for DroneMapping are from our pricing page. Stockpile Reports details come from its pricing page, checked in October 2026.
| Method | Software cost | Who stands next to the pile | Surface saved |
|---|---|---|---|
| Eyeball or tape estimate | None | A person on foot | No |
| Walking GNSS survey by a crew | Per visit, quoted | A surveyor on foot | Points only |
| iPhone walk-around app | Stockpile Reports Business plans are $1,000, $2,000 and $5,000 a year for 10, 20 and 50 piles | A person on foot, pile by pile | Per pile |
| Drone flight with DroneMapping | Starter $588, Team $1,488, Business $3,588 a year, any number of piles | Nobody | Whole yard |
A phone app suits a small yard where one person already walks the piles. A drone suits a yard with dozens of piles, haul traffic or tall faces. The side by side is on the Stockpile Reports alternative page, and if you are weighing a quoted platform, see the Propeller Aero alternative.
Honest fit
When this is not the right tool
DroneMapping processes up to 500 photos per flight, so a very large site needs two flights. A drone count needs a pilot with a Part 107 certificate for work done for pay, covered on the FAA commercial operators page. It does not weigh anything: the tons are only as good as your density factor. Covered bins and piles hidden under a roof need a base elevation you type in, and a pile under a conveyor or inside a building may be better measured another way.
Try it first
Measure a pile in the demo
The demo loads a stockpile yard on a public elevation surface. Click around a pile, pick a base plane and read area, cut, fill and net volume. No account is needed.
Pricing
What a yard pays for a monthly count
Starter is $99 a month or $588 a year with 3 seats and 3,000 images a month, enough for one yard flown once a month. Team is $249 a month or $1,488 a year with 10 seats, 15,000 images a month and PDF stockpile reports. Business is $599 a month or $3,588 a year with 25 seats, the progress timeline and change detection for operators with several yards. Compare against other tools in drone mapping software pricing.
Questions
Stockpile inventory software FAQ
It is software that measures the volume of each pile in a yard and turns it into an inventory figure. With drones, the volume comes from a surface model built from the flight, and tons and dollars come from your density and cost per ton.
Multiply volume in cubic yards by the loose density of the material in tons per cubic yard. Take the density from your own weighed loads. A pile of 4,200 cubic yards at 1.4 tons per cubic yard is 5,880 tons.
Monthly is the common rhythm for yards that close their books each month, and quarterly is the minimum for most audits. Flying the same toe lines each time makes the months comparable.
Yes, up to 500 photos per flight. A typical yard fits in one or two flights, and every pile in the surface can be measured afterwards.
Yes. The measurement table exports as CSV on every plan, with pile name, material, volume and the base plane used. Add your density and cost columns for tons and dollars.
For a count you can defend, control helps. Team and above accept GCPs and checkpoints and return an accuracy report in X, Y and Z.
Related pages
More for yards and quarries
- Stockpile Reports cost by pile count, with a 35 pile yard over 3 years
- Stockpile volume measurement for base plane methods and reports
- Best automated stockpile measurement software with a 3-year cost for a 25 pile yard
- Cut and fill software for earthwork volumes
- Landfill drone survey software for airspace and cell volumes
- Drone survey software for GCPs and contours
- Construction drone software for weekly progress
- Best drone mapping software compared on price and fit
Put next month's yard count on a map
Fly the yard, measure every pile and take the tons to the close.