DroneMapping

Drone roof inspection software for roofing contractors that turns a flight into a measured, marked-up client report

Drone roof inspection software stitches the photos from a roof flight into one high-resolution map, lets you measure areas and lengths on it, mark every defect and send the homeowner or adjuster a single link. DroneMapping does this in the browser. Upload the photos, get an orthomosaic sharp enough to read shingle damage, flashing and ponding, and on Team and above a 3D model for dormers and facades. Team is $1,488 a year with 10 seats, so an estimator, a crew lead and the owner all open the same job.

Try the demo
Earthworks pad, sample
Loading sample

net volume

Measurements
Area
Perimeter
Cut
Fill
Base plane method

After the flight

Why four hundred loose photos lose the sale

A roof flight returns hundreds of overlapping photos. Sent as a folder they prove little: the homeowner cannot tell which slope a photo shows, and the adjuster cannot tell how large the damaged area is. One stitched map puts every photo in place, so a finding has a location, a size and a record you can show again next spring.

  1. 01

    Every finding tied to a spot on the roof, not a file name

  2. 02

    Areas, lengths and perimeters measured on the map

  3. 03

    One branded link instead of a zip file of photos

Maps and models

An orthomosaic sharp enough for shingles, seams and flashing

Fly low and the ground sampling distance gets small enough to read granule loss, lifted shingles, membrane seams and debris in drains. The orthomosaic exports as GeoTIFF, JPG and PNG on every plan. On Team and above the same upload also produces a 3D textured model (OBJ) and a point cloud (LAS, LAZ), which is where steep slopes, dormers, chimneys and the facade below the eave are easiest to review. For vertical surfaces, add oblique passes around the building to the overhead grid. Not sure which altitude fits your camera? The ground sampling distance calculator gives it in seconds.

Roofer uploading drone photos from a truck tailgate before the client call

Worked example

From a plan-view area to roofing squares

An area measured on an orthomosaic is the plan-view area, the footprint seen from above. A sloped roof has more surface than its footprint, so the slope has to be added back. Take a house with a 2,400 square foot plan-view roof area and a 6 in 12 pitch.

Step Value
Plan-view area measured on the map 2,400 sq ft
Slope factor for 6 in 12 pitch (square root of 1 plus 0.5 squared) 1.118
Roof surface area about 2,683 sq ft
Roofing squares (100 sq ft each) about 26.8
With 10 percent waste on a cut-up roof about 29.5 squares

Measure each slope or section separately when pitches differ, then add them up. Export the measurements as CSV and drop them into your own estimate or report template.

Findings

Mark every defect and keep the conversation in one place

On Team and above you place annotations directly on the map, add a comment to each and keep the back and forth with the client or adjuster on the same page. The share page carries your logo and colors, so the homeowner sees your company, not a software vendor. View links open in any browser without a seat, with an optional expiry date.

  • Annotations and comments on the map
  • Branded client share page
  • View links with optional expiry
  • CSV export of measurements for your written report

Who it fits

Roofing contractors, inspectors and drone service providers

A roofing contractor uses the map to quote storm damage without climbing every roof. An independent inspector keeps one record per property and compares the same roof year over year. A drone service provider flying for several roofers keeps a project per client. Business adds project roles so each client sees only their own jobs, a progress timeline and change detection between two flights. More on the wider workflow is on the drone inspection software page, and the construction drone software page covers sites still being built.

Honest fit

When this is not the right tool

DroneMapping processes up to 500 photos per flight, which covers a house or a commercial roof but not a whole subdivision in one run, so split big sites into flights. It does not process thermal imagery, so it will not replace an infrared moisture survey. And if all you need is a one-page roof measurement report for an insurance claim, a dedicated roof measurement service is built for exactly that. Choose DroneMapping when you want your own flight, your own markup and a link carrying your brand. Flying for pay in the US also means a Part 107 remote pilot certificate, covered on the FAA commercial operators page.

Try it first

Check your roof flight in the demo

Drop your photos into the demo and it reads the metadata in the browser: camera, focal length, altitude, ground sampling distance and footprint per image. It shows whether the flight is ready for mapping before you spend a processing run. Nothing is uploaded.

Pricing

What roofing teams pay

Starter is $99 a month or $588 a year with 3 seats and 3,000 images a month, enough for a small crew that needs maps and measurements. Team is $249 a month or $1,488 a year with 10 seats, 15,000 images a month, the 3D model, annotations and the branded share page. Business is $599 a month or $3,588 a year with 25 seats. See the cost side by side with other tools in drone mapping software pricing, or read what it costs a roofing contractor in our drone roof inspection software cost breakdown.

Compare drone mapping pricing

Questions

Drone roof inspection software FAQ

It depends on what you hand the client. For a branded map with measurements, annotated defects and a shareable link that several staff can open, a seat-based cloud platform such as DroneMapping fits. For a single measurement report on a claim, a roof measurement service is quicker.

Yes. You measure areas, lengths and perimeters on the orthomosaic. The result is plan-view area, so apply the slope factor of each section, for example 1.118 for a 6 in 12 pitch, to get roof surface and roofing squares.

Any drone camera that records GPS in the photos works. A 20 megapixel camera flown low gives a small ground sampling distance, and a defect should span several pixels to be recognizable. Use the calculator to find the altitude for your sensor.

No. They open a view link in any browser, see the map, the model on Team and above, and your annotations, and reply in the comments.

Yes, on Business. The progress timeline lines up flights of the same roof and change detection highlights what changed between them.

Up to 500 photos per flight. A single house is a short flight, and a large commercial roof can be split into two flights.

Send the homeowner a measured, marked-up roof map the same day

Upload the flight, measure the slopes, mark the damage and share one link under your brand.